0 item(s) - USD 0.00

Serpent S120 PRO 1/12 2WD Pan Car Kit EP

USD 256.90 USD 332.90 (Save 22.8%)

Please log in to receive a notification when this item arrives in stock.
Out Of Stock!


Photo(s) for reference only


Tags: Serpent Pan Car

Serpent S120 PRO 1/12 2WD Pan Car Kit EP #410007

Description:

This is Serpent S120 PRO 1/12 2WD Pan Car Kit EP. The S120 pro is a revolutionary innovative 1/12th scale car design based on the F110 SF4. New innovative design for the rear pod with side bearings in linear guides replacing the sidelinks. With a traditional sidelink design, designers use long side links to have the relative roll movement between pod and chassis as linear as possible. But no matter how long the links are, there is always a longitudinal component in the roll motion. With the new side-bearing design, the roll motion is completely linear and independent thus the cornering is completely independent from accelerating or braking. While it doesnt change much on the mid corner handling of the car, this gives an unprecedented consistency and stability at corner entry when the braking and steering input overlaps and at corner exit when the throttle is applied before the steering is completely straight. What you feel is, you can brake harder into the corners and accelerate earlier out of corners. Lipo longitudinal or Lipo transversal with narrow chassis design. The new side bearing design opens the possibility to use both inline. And cross lipo orientation while keeping a narrow chassis design. Special holders for inline lipo configuration included in the kit, optional for lipo cross configuration. Full strength topdeck to prevent longitudinal flex and keep torsional flex on a reasonable level. 2 body mount positions are included. It does not need to be removed to exchange the lipo in any configuration. 1-screw Lipo mount in all lipo orientations. For the inline lipo orientation, the lipo is held by an aluminium holder that can be removed though the chassis bottom. For the transversal lipo orientation, the lipo can be pulled through the side. This is possible thanks to the no-link design. No more excuses not to charge the lipo in the car. The easy to work on and strong front suspension from the F110 SF4 is evolved for the pancar specific demands. All screws are easily accessible. Double short tube system for the rear roll damping. Compared to a single tube design, it gives a 100% symmetric driving feel. The tubes also work as roll limiter, which reduces the risk of dirt getting into the tubes or oil leaking out from them. New ultra-low center of gravity rear pod. The angled rear plate gives torsional stiffness, protecting the rear shaft and bearings, while keeping all masses low in the pod. This increases rear grip of the car, and preventing grip roll in high grip conditions. The carbon shaft is reinforced by an aluminium sleve at the bearing and where the pin connects the aluminium thread insert with the shaft. This makes the shaft one of the strongest on the market. With the bigger (8mm) bearing on the right side also helps with the higher load of the right side bearing because of the bigger leverage and the spur gear. The thread insert goes all through the shaft until the pin, so the tension force of the thread does not pull on the gluing. New improved shocks, much easier to build, with same, bigger piston diameter as the Project 4X, and the Project 4X bleeding hole for easy rebound adjustment. After the huge success of the F110 SF4, The step to develop a 1/12th scale car on the same platform was logical. The focus was to make the car easy to work on and durable without sacrificing performance. We proudly present another Masterpiece of innovation and performance. Enjoy the assembly and feel the difference at the racetrack.

Specification:

  • Trackwidth: Front 168mm Trackwidth Rear 169.5mm (adjustable with shims)
  • Wheelbase: 202mm
  • Rear adjustable range: +2mm (shims)
  • Front adjustable range: +3mm (inserts in 0.6mm steps)

Include:

  • Serpent S120 PRO 1/12 2WD Pan Car Kit EP (1 pc)

Require:

  • 2.4GHz Radio System
  • Motor & ESC
  • Steering Servo
  • Tires & CA Glue
  • Body & Polycarbonate Paint
  • LiPo Battery
  • Compatible Battery Charger
Rcmart Description
Brand Serpent
Completeness Unassembled
Drive Train 2WD
Power Plant Electric
Scale 1/12
Vehicle Type Pan Car

Write a review

Please login or register to review

Customers that bought this also purchased...

Yeah Racing YA-0594OR
RC Body Clip For 1/8 1/10 1/12 10pcs Florescent Orange
USD 4.50
Sale
Tamiya 51589
On Road Racing Truck Tires 2pcs For TT01 TT02 Trucks
USD 8.55 USD 9.50
Yeah Racing AHP-310OR
Aluminum 7075 3x10mm Hex Socket Button Head Screws 10pcs Orange
USD 5.90
Samix SCX3-4067
Brass Knuckle Busings Set For Axial SCX10 III Capra
USD 4.50