NOVAK Hammer ESC w/ NX4 3900Kv Sensored Brushless 4-Pole Motor Combo #3310
The Novak Hammer SCT 1/10 Scale Brushless ESC/NX4 Motor Combo delivers 100% pure, sensor-based control and precision driving to enthusiasts looking for an incredibly smooth-driving, affordable, power upgrade for their 2WD 10th scale off-road short-course truck, 4WD or 2WD off-road buggy, and even power-hungry on-road cars.
Novak's Hammer ESC is compatible with 2S and 3S LiPo batteries, is pre-wired from the factory with gold-plated bullet connectors, and the battery wires are open ended and pre-tinned ready for the battery connector of your choice! The ESC is based on Novak’s proven 1/10th scale ESC design. Drivers new to the Novak platform will experience a much more connected feel to their vehicle with strong braking control. The Hammer is factory-defaulted to LiPo mode with reverse turned on. Drivers can customize the Hammer firmware to suit their driving style, including Throttle Curve, Brake Power and many other parameters. No clumsy or complicated programming device needed – the Hammer is fully programmable with a press of a button!
The Novak NX4 540 4-Pole Sensored Brushless Motor offers 100% pure, sensor-based control and precision driving to enthusiasts looking for an affordable, incredibly smooth-driving brushless motor for their 2WD 10th scale off-road short-course truck, 4WD or 2WD off-road buggy, and even power-hungry on-road cars. The NX4 540-size motor easily fits into any 1/10th scale vehicle. It boasts 3,900Kv of pure sensor-based power, and includes a large-diameter Neodymium rotor for that extra torque needed. It is factory wired with heavy-gauge silicone wire for easy installation, and includes replaceable power wires for drivers wanting more custom installs – a feature not common on similar motors in the market.
- Motor Type: Sensored Brushless (2 and 4-pole)
- Fwd/Brk/Rev: F / B / R
- Input Cells (LiPo/Ni-MH): 2S and 3S LiPo/LiFe or 4-9 NiMH
- Dimensions (in/mm): 1.4" x 2.0" (35 x 51 mm)
- Height (in/mm): 0.9" (24 mm)
- Weight (oz/g): 1.4 oz. (40 g)
- On-Resistance (ohms): 0.00060 ohms @ 25°C trans. temp.
- Motor Limit:
- 2S: 4,500Kv (4-pole) or lower; 8.5T (2-pole) or higher sensored
- 3S**: 3,900Kv (4-pole) or lower; 10.5T (2-pole) or higher sensored
- BEC (volts / amps): 6.0 volts DC / 3.0 amps
- Wire Size (GA): Motor: 13G Super-Flex Copper-Strand Silicone Wire, factory-installed with 4mm female gold-plated bullet motor connectors (black with color-coded heat shrink: blue, yellow, orange)
- Battery: 14G Super-Flex Copper-Strand Silicone Wire, factory-installed (red/black)
- Status LEDs: 5, multi-colored
- Design: 4-pole sensor-based
- Weight: 5 oz (142g) with power wire and sensor harness
- Input Voltage: 2S and 3S LiPo/4-9 NiMH
- Kv (unloaded): 3,900 RPM/Volt
- Maximum RPM: 50,000
- Diameter: 1.4" (36mm)
- Length: 2.1" (53mm)
- Shaft Diameter: 1/8"
- Mounting: 25mm diameter (M3x0.5mm)
- Rotor Magnet: 4-pole Sintered Neodymium
- Rotor Diameter: 18mm Kevlar-wrapped
- Stator: 12-slot, 2Y, epoxy dipped
- Connector Type: 13GA Super-Flex Copper-Strand Silicone Wire, factory installed with 4mm male gold-plated bullet connectors
- Recommended ESCs: Novak Hammer, GTB3, Crusher
- NOVAK Hammer ESC (1 pc)
- NX4 3900Kv Sensored Brushless 4-Pole Motor (1 pc)
- Sensor Cable (1 pc)
- Mounting Hardware (1 pack)