NOVAK Mongoose Micro Brushless System - 10.5T
Description:
This is the Novak Mongoose 10.5 Micro Brushless System with the Three-80 8.5 Turn Motor and the Mongoose Micro ESC for 1/18 and 1/16 scale Cars.
Novak has bred a micro brushless system: the Mongoose Micro Brushless System. This system includes the Novak Mongoose Brushless/Brush ESC factory-wired to one of three Novak Three-80 Micro Pro Brushless Motors. The Three-80 Micro Pro is the first sensor-based brushless motor that is specifically designed for 1/18 and 1/16-scale cars. Because it is sensored and lightweight, it gives these micro scale cars the ability to maneuver at high speeds in extremely tight spaces, all with unsurpassed low speed and braking control. The Mongoose’s Brushless/Brush ESC and sensored brushless motor are perfectly matched to maximize performance and handle with the agility and speed of a mongoose.
FULLY FEATURED ESC
The Mongoose Micro Brushless/Brush ESC is a versatile, fully featured speed control specifically developed for micro applications. In addition to its compatibility with both brushless and brush motors, it instinctively knows via its Auto-Detect Brushed Mode when a brush motor is connected. Additional features of the Mongoose Micro ESC are its on-board programmability, built-in 2S & 3S Li-Po Cut-off Circuitry, heavy duty 6.0V/2A BEC and a water-resistant case.
Feature:
ESC
Three brushless throttle profiles specifically designed for micro vehicle applications and one brushed throttle profile (features built-in Auto Detect Brush Mode)
Compatible with 380-size or smaller brush motors and Novak Three-80 Series brushless motors
Complete, on-board programming via Novak’s One-Touch button and 4 status LEDs.
Adjustable parameters include Minimum Brake, Drag Brake, Dead Band and Minimum Drive, as well as Drive Frequency (in brush mode)
Built-in 2S & 3S Li-Po Cut-off Circuitry (can be activated in any of the throttle profiles)
Novak’s One-Touch Set-Up™(still the easiest)
Gold-Plated PCB Direct-Solder Wiring Tabs for flexible soldering options
Plug-in input harness (#5304) and user-replaceable switch harness (#5600)
Replaceable Power Trans-Cap Module (#5683)
Lightweight 16GA Silicone Battery and Motor Wire (replaceable)
Built-in Power Output for Optional 6V Accessory Fan (#5647)
Water-resistant case
Factory-installed heat sink
Thermal Overload Protection
Novak’s Radio Priority Circuitry™and Polar Drive Circuitry™
Meets RoHS compliance and includes 120-Day Warranty
Designed and built by Novak in Irvine, California using globally-sourced components
Motor
380-size brushless motor specifically designed by Novak for 1/16th to 1/18th scale micro vehicles
Sensor-based design for complete throttle control
High-performance Nickel-plated Sintered Neodymium rotor for maximum motor acceleration, braking power and performance in high-temperature conditions
Oversized, rugged front bearing for increased load handling and bearing life
Multiple motor mount screw patterns
Lightweight ribbed aluminum end bells
Specification:
ESC
Input Voltage: 2-3 Li-Poly cells or 4-9 Ni-MH/Ni-Cd cells (1.2V/cell)
Forward/Reverse: FWD/BRK/REV (brushless mode); FWD/BRK (brush mode)
Motor Limit: any Novak Micro (brushless); any 380-size (brushed)
Size: 1.15" x 0.95" (29 x 24.3mm)
Weight: 0.77 oz. (21.7 grams)
Rated & Braking Current: 40 amps per phase (brushless/brush)
Power Wires: 16-gauge
BEC: 6.0 volt/2.0 amps
Voltage Cut-Off: 6.25 volts (2S), 9.375 (3S) [when Li-Poly Cut-Off Circuitry is enabled
Motor Plug: 2 mm connectors
Motor
Input Voltage: 2-3 cell Li-Po or 4-9 Ni-MH/Ni-Cd cells (1.2 V/cell)
Watts: 165
Kv (unloaded): 7300
Size: 380 size: 1.02" D x 1.48" L (26 D x 37.7 L mm)
Motor Weight with Wires: 2.54 oz. (72 grams)
Shaft Diameter: 1/8" (accepts all existing pinion gears)
Bearing Size: Oversized (1/2" x 3/16") Front; Standard Rear (7mm x 3mm)
Magnet: Sintered Nickel-plated Neodymium (one-piece, multi-pole cylindrical)
Include:
Novak Mongoose Electronic Speed Control (1pc)
Novak Three-80 10.5turn Brushless Motor (1pc)
Instruction Manual
Note
Novak's Mod 0.5 and 0.6 Aluminum PinionGear Sets include three gears that fit seamlessly with Novak's Three-80 Micro Pro Brushless Motor, which has a 1/8" output shaft.
Compatibility
Mod 0.6: For DuraTrax Vendetta line
Mod 0.5: For Associated, Kyosho and Team Losi's micro vehicles, as well as Tamiya's TamTech line.
#5200 Mod 0.6 Set: 11T/12T/13T
#5210 Mod 0.5 Set: 11T/12T/13T
Works well on small, tight tracks
#5201 Mod 0.6 Set: 14T/15T/16T
#5211 Mod 0.5 Set: 14T/15T/16T
Excels on medium-sized tracks
#5201 Mod 0.6 Set: 14T/15T/16T
#5212 Mod 0.5 Set: 17T/18T/19T
Performs great on large tracks
|
rcMart.com © 2001 - 2013
Facebook
Twitter
Google+
Youtube
Blog