MST MS-01D VIP II 1/10 4WD Drift Car Kit 532025 w/ OMG Low Profile Brushless Digital Servo BM07S #CB0817
Please noted that the ETA of this product will be 3-4 weeks after the payment confirmed and subject to change.
- MST MS-01D VIP II 1/10 4WD EP Drift Car Chassis SSG Silver Surface Graphite Red ARR #532025
- OMG High Voltage Low Profile High Speed Brushless Digital Servo 7KG 0.05Sec For RC Drift Car #D2-LP-BM07S
MST MS-01D VIP II 1/10 4WD EP Drift Car Chassis SSG Silver Surface Graphite Red ARR #532025
The new MST MS-01D VIP II is now available to order! The MS-01D VIP II is the top of the line in RC drifting, with 98% of our upgrades included. This new version is available in red or silver aluminium with black or SSG slimline carbon. Avoid spending thousands of pounds on other chassis to make them do what the VIP does out of the box.
The VIP is a "no compromise" chassis, including CS gears, huge angle, massive tuning potential and very intellegent design features, making tuning fun! The VIP can also be converted to make a Luxury version of the FS-01D uising the optional front motor conversion kit.
Note: The car illustrated comes with carbon graphite parts in black, which those parts are in silver (SSG) in this model.
- 95% factory pre-assembled kit. (ARR)
- High-end MS-01D chassis with 98% hop-ups!
- New carbon chassis set
- Carbon battery mount
- Aluminum front & rear steering knuckle
- Aluminum damper set
- And other completed aluminum parts!
- Wheelbase: 257mm (adjustable 255mm to 259mm)
- Tread Front and Rear: 186mm (adjustable 186mm to 190mm)
- Gear Ratio: 2.0 (36T/18T)
- CS ration: 1.32 ( 40T/16T )
- Drive System: 2 belts/4WD
- Damper: Oil damper
- Suspension: A-arm (double wishbone) with pillow-ball suspension system
- Steering tie-rod: Division into three
- Bearing: Full ball bearings
- Caster: Variable 4, 7, 10, 14 degrees
- Camber: 0 to 12 degrees
- #210101 - Aluminum servo mount
- #210102 - Aluminium one way unit
- #210103 - One way joint
- #210105 - Turn-buckle shaft 3x60mm
- #210109 - Turn-buckle shaft set (for ms-01d 20x2/25x4/28x2)
- #210110 - Stabilizer set
- #210111 - CS pully set (1.54/1.66/1.82)
- #210114 - Aluminium motor heat sink mount
- #210115 - Aluminium damper set (4)
- #210116 - Aluminium spur gear holder cover
- #210117 - Aluminium spur gear holder
- #210118 - Aluminium upright
- #210269 - Aluminium ackerman adjustable upright
- #210121 - Aluminium spool unit
- #210122 - Aluminium steering arm
- #210123 - Aluminium belt stabilizer mount
- #210124 - Aluminium belt pully
- Full SSG chassis set including front and rear upper decks, lower deck, front and rear shock towers and battery tray
- #210134 - Aluminium upper bulkhead R/L X2
- #210135 - Aluminium main shaft mount R/L
- #210136 - Aluminium bulkhead R/L X2
- #210143 - Aluminium wheel hubs (Brake Disc Shaped X4) with brake calipers
- #210144 - Coil spring set 28mm (8)
- #210142 - Aluminium bumper brace
- #210146 - Steel 60 degree drive shafts
- MST MS-01D VIP II 1/10 4WD EP Drift Car SSG (1 Set)
- Tire & Wheel
OMG High Voltage Low Profile High Speed Brushless Digital Servo 7KG 0.05Sec For RC Drift Car #D2-LP-BM07S
The HDT045070B servo is a low profile, powerful, accurate ultra speed precision digital servo with its heat sink aluminum case, long wear 7075 Aluminum anodize titanium gears, a precision brushless motor and improved electronics, legendary quality.
It can be capable of 6.0 to 7.4 volt operation.
The HDT045070B takes a whole new galaxy of performance.
RC OMG provide legendary digital precision with higher torque and faster speed servos.
When Buy at rcMart, This Brushless servo are warranted for three years from the date of purchase to be free from manufacturing or component defects. During the warranty period RC OMG will repair or replace (at our discretion) any defective products. Please keep your original order receipt as proof of the date of purchase.
This warranty does not cover abuse, neglect, or damage due to incorrect wiring, over voltage, overloading, misuse, crash damage, improper installation or damages caused by alteration by unauthorized persons.
- For: 1/10 Drift
- Material: Aluminum
- Gears: Long Wear 7075 Aluminum Anodize Titanium
- Super high 12 bit (4096) resolution
- Robust output for superb response in extreme maneuvers
- Zero dead band assures legendary precision
- Aluminum middle case helps dissipate heat
- Digital precision provides great accuracy and performance
- Ball bearing-supported output 25T shaft
- Compatible with all types of Radio system
- Pulse width travel is adjustable
- Type: Digital
- Operating Voltage Range: 6.0-7.4Volts DC
- Bearing Type: Dual Ball Bearings
- Speed (s/6)0░@6.0 /7.4V: 0.06/ 0.05
- Torque oz./in. (6.0V/7.4V): 76/97
- Torque kg./cm. (6.0V/7.4V): 5.5/7
- Dimensions: 40.2mm x 20.1mm x 25.2mm
- Weight: 45g
- Motor Type: Brushless motor
- Control System: +Pulse Width Control 1500usec Neutral
- Required Pulse: 3-5 Volt Peak to Peak Square Wave
- Operating Temperature Range(℃): -10░ - 50░
- Idle Current (@6.0V/7.4V): 4mA/5mA
- No Load Running Current (6.0V/7.4V): 300mA/400mA
- Stall Current (6.0V/7.4V): 3200m/3900mA
- Dead Band Width: 2Ás
- Potentiometer Type: Rotating(Max.220░)
- Connector Wire Length: 11.8 in. / 300 mm.
- Connector Wire Gauge: 25 AWG
- Connector Type: JR
- Gear Type: Titanium Gears
- Frequency: 330Hz
- Shaft: 6mm 25T
- High Voltage Low Profile High Speed Brushless Digital Servo (1 pc)