MST CMX 1/10 4WD High Performance Crawler Car L Kit #532144
This is MST CMX 1/10 4WD High Performance Crawler Car L Kit.
*Photos for reference only.
Shaft-Driven Full-Time 4WD
Heavy Duty CVA Front Shaft
Good efficient transmission gear set 10 Front and Rear Solid-axle
Transmission Dust Cover
Realistic Steel C-Channel Frame
Great steering angle
Realistic Scale Tire
Wheelbase: 242 / 252 / 267 mm (Adjustable)
Gear ratio: 1 : 19 - 1 : 42.6
Tire Width/Diameter: 30x90mm
MST CMX 1/10 4WD High Performance Crawler Car L Kit
Tire and Wheels
540 Type Motor
Yeah Racing Tritronic 1/10 Waterproof Brushed 60A ESC #ESC-1060WP
After the revolutionary Hacktronic ESC introduction, Yeah Racing is now introducing the almighty Tritronic 1/10 Waterproof Brushed 60A Electronic Speed Controller ESC. It is water-proof & dust-proof, making it almighty to race under all weather condition. It has 3 running modles compatible to various vehicles and multiple protections in case of low voltage, over-heating or Throttle signal loss.
For: 1/10: Touring Car, Buggy, Short Course Truck, Monster, Truggy, Rock Crawler and Tank
Water-proof and dust-proof, suitable for all-weather condition races.
Small size with built-in capacitor module.
Fwd/Rev/Br running mode fits for various vehicles (Fwd =Forward, Br=Brake, Rev=Reverse).
Great current endurance capability.
Great built-in BEC output capacity.
Automatic throttle range calibration, easy to use.
Easy to set the ESC parameters with jumpers.
Multiple protections: Low voltage cut-off protection for battery / Over-heat protection / Throttle signal loss protection.
Fwd. Cont. / Peak Current: 60A /360A
Rev. Cont. / Peak Current: 30A /180A
Voltage Range: 2-3S Lipo or 5-9 NiMH
Cars Applicable: 1/10: Touring Car, Buggy, Short Course Truck, Monster, Truggy, Rock Crawler and Tank
Yeah Racing Tritronic 1/10 Waterproof Brushed 60A ESC (1 Set)
Manual (1 pc)
Yeah Racing Hackmoto V2 35T 540 Brushed Motor #MT-0014
This Yeah Racing Hackmoto V2 Modified brushed motor series are high performance 540 motors designed exqusitivly for competitive RC usage.
Hackmoto V2 featured premium quality material with high strength magnets for unmatched brushed motor speed and torque. Beside of its performance, the motor featured direct-solder wiring tabs for flexible soldering options. It is also designed to be rebuildable with an easily accessible commutator and replaceable brushes and springs. The motor also adapted dual-ball bearings design yields better performance, allowing a smooth ride, precise control with best possible efficiency.
For: 1/10 RC Car
Rebuildable with an easily accessible commutator and replaceable brushes and springs
High strength magnets for unmatched brush-motor performance
Specifically designed for R/C vehicles that require precise movement control
Excellent torque and long-run times
Direct-Solder Wiring Tabs for flexible soldering options
Dual-ball Bearings Design
Input Voltage: 7.4v
Max. Input Voltage: 11.1V
Shaft Length: 13mm
Yeah Racing Hackmoto V2 35T 540 Brushed Motor (1 pc)
Yeah Racing (#MG-48019) Aluminum 7075 Hard Coated Motor Gear/Pinions 48 Pitch 19 Teeth
The motor gear series including 2 major types of Pitch Pinion - the 48 Pitch Pinion and the 64 Pitch Pinion. The 48 Pitch Pinion available from 15 teeth to 38 teeth. The 64 Pitch Pinion available from 17 teeth to 52 teeth. The Yeah Racing Aluminum Motor Gear are made by 7075 high quality aluminum with titanium coated surface.
For: 1:10 EP, fit on 540 Motor
Material: 7075 Aluminum
48 Pitch Pinion 19 Teeth (1 Pc)
Set Screw (1 pc)
How to calculate Final Gear Ratio?
For example, if your car has the following setting:
Motor Gear: 25
Spur Gear: 84
Gear Differential: 38
Firstly, we need to calculate the 'Motor Gear to Spur Gear Ratio', divide 84 by 25 equal to 3.36. Then we need to calculate the 'Pulley to Gear Differential Ratio', divide 38 by 19 equal to 2. Finally, the 'Final Gear Ratio' is 3.36 x 2 = 6.72.
Motor Turn used based on Final Gear Ratio:
The above guideline is for reference only. The recommended motor turn may vary depending on different brands. More information can be found on motors' official websites.
Power HD 4.8-6.6V SUPER TORQUE Digital Servo 0.16sec/277.7oz-in/20kg-cm For Crawler / Buggy / On-road #LF-20MG
This is Power HD 4.8-6.6V SUPER TORQUE Digital Servo 0.16sec/277.7oz-in/20kg-cm For Crawler / Buggy / On-road #LF-20MG. Power HD LF-20MG is an excellent budget Digital Metal Gear servo for 1/10 & 1/8 cars,30CC or 50CC planes. Middle aluminum casing for extra cooling and copper metal gears sure can't beat the price and performance of this servo.
For: Crawler / Buggy / On-road
Material: Middle Aluminum Casing With Plastic Top and Bottom
Color: Red and Black
Copper & Aluminum Gear
Torque(4.8V): 16.5 kg-cm (229.1 oz/in)
Torque(6.6V): 20.0 kg-cm (277.7 oz/in)
Speed: 0.18 sec (4.8V) │ 0.16 sec (6.6V)
Operating Voltage：4.8 ~ 6.6 DC Volts
Weight: 60 g (2.12 oz)
Bearing Type：Ball Bearing x 2
Motor Type：DC Motor
Gear Type：Copper & Aluminum
Working frequence：1520μs / 333hz
Size：40.7 x 20.5 x 39.5 mm ( 1.60 x 0.80 x 1.55 in)
Power HD 4.8-6.6V SUPER TORQUE Digital Servo 0.16sec/277.7oz-in/20kg-cm For Crawler / Buggy / On-road #LF-20MG (1 pc)
Yeah Racing RC Ball Bearing Set with Bearing Oil For MST CMX #YB0288MX
RC Ball bearings should always be your first upgrades, it reduces friction for less rolling resistance, and that means higher speed and longer the running times. RC Ball bearings hardly require maintenance and last a lot longer than stock Oilite bushings.
Yeah Racing RC Ball Bearings have the lowest resistance. They are manufactured by Aircraft quality steel. Pre-lubricated to ensure its excellent performance!
These high quality bearings outweigh the other low quality one:
Aircraft quality material
*Now comes with bearing oilfor maintaining bearings in long run. (This new bearing set (with bearing oil) will replace the old item.)
Onisiki's 2 channel 2.4Ghz Radio Kit with a receiver that features failsafe function which aims to prevent any accidents if your battery runs out on either on receiver or transmitter. If the Receiver is not able to receive any signal, from the control to Throttle, the parameter of Throttle on Receiver will turn back to its original setting! Features dual rate control and servo reverse for any custom rc enthusiast!
Pretty much everything you need to get your own custom crawler started. The esc and motor is terrific for crawling. Servo is plenty of power and torque that will be needed. The transmitter is very easy to set up and use and is comfortable in the hands. the only thing you need is a battery and charger. NiMh battery works well if you don't want to go LiPo at first. You will also need a suitable body for this chassis. The Volkwagen Amarok, Toyota FJ Cruiser fit perfectly.