Xpress (MRR2-PRO) 1:10 Mini Road Runner II - Pro Kit (Version 2.1) x 1 pc
Hobbywing EZrun-60A-SL-H ESC (Version 2.0 USB Supported) x 1 pc
Yeah Racing (#BM-0009) Ultimate Brainpower 12T Sensorless Brushless Motor x 1 pc
Yeah Racing (#LP-0036) LiPo Racing Pack 7.4V 3600mAh 20C x 1 pc
Futaba (#2PHKA-AM) MEGATECH JUNIOR (MJ) 2-CH Radio Control System x 1 pc
COLT (#M2309) 1/10 Mini Body Swift x 1 pc
Combo Price Now at USD$299.99
Save USD$139.7(Over 30% OFF)
Xpress (MRR2-PRO) 1:10 Mini Road Runner II - Pro Kit (Version 2.1)
The major advancements of this new Pro Kit are a lower centre of gravity of the gear system and re-distribution of the weight ratio for the major chassis components to achieve a 50:50 balance ration. The body chassis is in silver dual deck woven graphite that looks very appealing. On its body chassis, it adopts a popular left and right load balancing design. If you have a Junior Kit or an old version of Mini-Xpress, it could be easily upgraded to a new version that can be equipped with ABS plastic gear box plus FPR junior racer body chassis and a combination of aluminum gear box and woven graphite body chassis to a professional version of Xpress Pro Kit.
What's the difference between Old and New verison?
The main difference between Xpress Junior and Pro Kit is the material of body chassis. The new version of Mini-Xpress body chassis appears quadrangle, weight distribution is more balance, and base plate is 2 mm thick and lower centre of gravity of gear system. A newly designed aluminum main gear adaptor is also installed with fixed supports on both left and right sides to prevent distortion. The motor mount is with cavity that enables motor fixed even lower. The new version enables motor mount fixed at lower position, which enhances gear shaft height reduced by 26mm and this is even lower than other mini-racers in the market. The new version adopts dish wheel coated with red ring and wheel lock nut.
Turnbuckle camber/ caster link system
High efficiency 2 belt driven 4WD drive system
Low C.G. structure
32 Tooth differential pulley
Damper with tunable spring strength
High performance ball bearing
64 pitch spur delrin gear
Alloy motor mount
Drive ratio: 2.133
Note: Double sides tape is needed for installing 1:10 servo on the chassis. Or you can purchase the Yeah Racing (#SER-040RD) Alloy Servo Mount if you are installing a Mini servo
Chassis length : 283 mm
Gross weight : 523g (Junior kit) / 515g (Pro kit)
Width : 160 mm
Wheel base : 203-210 mm
Motor gear ratio : 3.605 – 13.657
Camber : Front/ Rear
Caster : Front
Toe-in : Front
Roll-Bar : Front/ Rear
Down-stop : Front/ Rear
NOT included in MRR2 Pro/ Junior Kit
Radio system (transmitter and receiver)
Steering servo (Width<20.6mm, Length<38mm)
Electric speed controller
Sub-C battery (6 cells 7.2V)
Hobbywing EZrun-60A-SL-H ESC (Version 2.0 USB Supported)
The EZrun series brushless controls (Version 2.0 USB Supported) include ESC of 18A, 25A 35A and 60A for RC cars and trucks.
The ESC is USB supported. The firmware of the ESC can be updated through an USB adapter on the Advanced LCD Program Box (Optional device).(NEW)
With 3 running modes: Racing mode (Forward), Forward/Backward mode and NEW Rock Crawler mode.
Especially designed for RC car, with excellent start-up, acceleration and linearity features
Compatible with sensorless brushless motor
Use top quality of electronic components to enhance the current endurance and capacity of the ESC.
4 steps of maximum reverse force adjustment
Proportional ABS brake function with 4 steps of 4th – 11th maximum brake force adjustment, 8 steps of drag-brake force adjustment and 4 steps of initial brake force adjustment.
9 start modes (Also called “Punch”) from “soft” to “very aggressive”.
Multiple protection features: Low voltage cut-off protection for lithium or nickel battery / Over-heat protection / Throttle signal loss protection / Motor blocked protection.
8 steps of timing adjustment.
Easily program with only one button and compatible with pocket-sized program card.
Cont. Current: 60A
Burst Current: 380A
Resistance: 0.0007 ohm
Suitable Car: 1/10 car
Suitable Brushless Motor: > 5.5T (3650 brushless motor)
Battery: 4-9 Cell Ni-xx (NiMh or NiCd) or 2-3 Cell Li-Po
BEC Output: 6V/1.5A
Motor Type: Sensorless Brushless Motor
Dimension: 31.5 x 27.5 x 24 (mm)
Weight: 32g (Without wires)
EZrun-60A-SL ESC (Version 2.0) (1 Pc)
Cable Tide (4 Pcs)
Shrink Tube (3 Pcs)
Hobby Wing Decal (1 Pc)
12T Sensorless Brushless Motor Set
This is the Yeah Racing series 12T Sensorless Brushless Motor for RC cars and trucks.
For: 1/10 RC
Operated with: Brushless ESC
Turns: 12 T
12T Sensorless Brushless Motor (1 Pc)
Click the image below to enlarge the Yeah Racing Ultimate Brainpower Brushless ESC & Motor Poster
Yeah Racing LiPo Racing Pack 7.4V 3600mAh 20C
This new li-po battery (LP-0036) is specifically developed for all 1/10 explosive RC cars. It makes the cars perform speedy! Most of the RC drivers comment it is a MUST buy item especially for the competition! The process of installation is very simple and time-saving which applies to all RC cars. Just strengthen your car with this powerful li-po battery!
Discharge rate: 20C
Voltage: 7.4 V
LiPo Racing Pack 7.4V 3600mAh 20C (1 pc)
For your safety, please read the instruction before use.
Click the icon below to download.
In addition, please make sure that other series of Li-Po Battery Pack within the positive and negative sides or wires are certainly correct before using. You are welcome to inquire us about the subject.
Users should charge the battery within 0.5C rate for the first 8 to 10 sequences.
Subsequently, 1C rate charging is good to maintain the lifespan of battery.
Of course, users may use higher C rate to charge but it will affect the battery performance even life cycle is still short.
Therefore, we recommend all users should follow the above instruction of battery charging.
MEGATECH JUNIOR (MJ) 2-CH Radio Control System
2 CHANNEL RADIO CONTROL SYSTEM
2-channel Digital Proportional R/C System For Cars, Boats
Yachts, and other Models
Transmitting frequency: 27MHz
Modulation method: AM
TX -T2PHKA X1
Allow longer control distance for Mini-X and Mini-Z
S3003 Servo (Standard Servo)
Power Requirement: 4.8V or 6V (common with receiver)
Current Drain: 8mA (AT 6v/ldle)
Output Torque: 3.2kg-cm (at 4.8V)
Operating Speed: 0.23sec/60 degree (at 4.8V)
R122JE Receiver (2Channels, AM Reciever)
Receiving Frequency: 27MHz
Power Requiremnet: 6V
COLT (#M2309) 1/10 Mini Body Swift
Unpainted Body with detailed decal
With 2Decal & Mask
M-Chassis (*Suggested Model : Tamiya M03, Xpress Mini)