3Racing Sakura D4 AWD 1/10 Drift Car Kit Pre-Assembled w/ Servo ESC 13T Motor 2.4Ghz Radio Beginner Combo #CB088
- 3Racing Sakura D4 AWD 1/10 Drift Car Kit Pre-assembled #KIT-D4AAWD
- Power HD High speed Digital lineary Servo 6V 7KG 0.06Sec For 1/10 RC Car #DS-1206TG
- Yeah Racing Spur Gear Support Plate Aluminum Pink #YA-0304PK
- Yeah Racing Tritronic 1/10 Waterproof Brushed 60A ESC #ESC-1060WP
- Yeah Racing Hackmoto V2 13T 540 Brushed Motor #MT-0012
- Onisiki 2.4GHz 2 Channel 2.4Ghz Transmitter w/ Receiver #ONI3701
3Racing Sakura D4 AWD 1/10 Drift Car Kit Pre-assembled #KIT-D4AAWD
The all new Sakura D4 Drift Chassis is 3Racing’s newest iteration of their drift platform. Do not be fooled by the price, it features parts which are option parts on cars twice the D4's price.
Featuring two battery locations, one infront of the motor and one on the rear diffuser to allow users to tune the weight distribution based on user's liking. Combining ideas and feedback from D3 users, the D4 was redesigned from the ground up and features new parts.
*Photo for reference only. Servo in the photo is not included
- Weight Distribution: Allows the battery to be mounted on the rear diffuser or infront of the motor.
- Steering: A redesigned steering rack which allows a larger steering angle when compared with the previous version.
- Drivetrain: Utilizing a belt drive system, which allows for quiet and efficent drivetrain. Features a rear spool and a front gear diff.
- Suspension: Suspension components have been completely redesigned to accommodate the large steering angle of this AWD drift car. Features Y arm suspension on the front which is seen almost all high end cars, will prevent the wheels from hitting the a-arm whilst at max steering angle.
- Oil Filled Coil Spring Shocks: Lengthen 55mm coiled spring oil filled shocks with threaded shock bodies allows a more progressive chassis roll action and easy tuning
- Molded Rear Diffuser: For an added touch of realism, a molded composite rear diffuser comes standard to give the Sakura D4 the extra attention to detail
- FRP Chasis : The Sakura D4 will be fitted with a FRP lower plate chassis designed with rigidity in mind to ensure efficient side to side weight transfer to easily initiate high speed drifting.
- 3Racing Sakura D4 AWD 1/10 Drift Car Kit Pre-assembled (1pc)
- Radio System (Min. 2ch)
- Pinion (48p, 22T recommended in manual)
- Battery (7.2V, this kit will fit both shorty packs and normal size)
Power HD High speed Digital lineary Servo 6V 7KG 0.06Sec For 1/10 RC Car #DS-1206TG
This is a Power HD High speed digital lineary servo that power HD described as the best choices for 1/10 on road rc. The servo is packed with high performance gear set as well as amazing speed and reliable torque that helps to gain excellent control and advantage in competitive racing. Gears are made of titanium shield 7075 grade aluminum for maximum durability and performance advantages.
- For: 1/10 RC on road
- Material: Titanium shielded 7075 Aluminum Gear
- Color: Black with Red
- Fit Futaba Servo Horn
- Model: DS-1206TG
- Speed: 0.07 sec (4.8V) │ 0.06 sec (6.0V)
- Torque(4.8V): 6.0 kg-cm (83.3 oz/in)
- Torque(6.0V): 7.0 kg-cm (97.20 oz/in)
- Operating Voltage：4.8 ~ 6.0 DC Volts
- Weight: 48 g (1.69 oz)
- Bearing Type：Ball Bearing x 2
- Motor Type：Coreless Motor
- Gear Type：Copper & Aluminum
- Operating Temperature：-20℃~60℃
- Working frequence：1520μs / 333hz
- Length: 40.3mm
- Width: 20.2mm
- Height: 26.1mm
- Digital Servo (1 set)
- Manual (1 pc)
Yeah Racing Spur Gear Support Plate Aluminum Pink For 1:10 Drift RC Spur Gear #YA-0304PK
This spur gear holder is made of lightweight rigid aluminum. It is not only aesthetically appealing; it is fully functional as well. It is able to fix the position of the spur gear, making it more rigid than before.
- For: 1:10 RC Spur Gear, Drift, Touring, Tamiya TA05 FF03 XV01
- Material: Aluminum
- Color: Pink
- Inner Diameter: 9.5mm
- Outer Diameter: 27.4mm
- Thickness: 3.4mm
- Spur Gear Support Plate Aluminum Pink (1pc)
- Screw (4pcs)
Reviews from RC Racer - May 2013
"I fitted the main spur with Yeah Racing gear support plate to ensure the pinion and spur stay nice and true to each other."
Yeah Racing Tritronic 1/10 Waterproof Brushed 60A ESC #ESC-1060WP
After the revolutionary Hacktronic ESC introduction, Yeah Racing is now introducing the almighty Tritronic 1/10 Waterproof Brushed 60A Electronic Speed Controller ESC. It is water-proof & dust-proof, making it almighty to race under all weather condition. It has 3 running modles compatible to various vehicles and multiple protections in case of low voltage, over-heating or Throttle signal loss.
- For: 1/10: Touring Car, Buggy, Short Course Truck, Monster, Truggy, Rock Crawler and Tank
- Water-proof and dust-proof, suitable for all-weather condition races.
- Small size with built-in capacitor module.
- Fwd/Rev/Br running mode fits for various vehicles (Fwd =Forward, Br=Brake, Rev=Reverse).
- Great current endurance capability.
- Great built-in BEC output capacity.
- Automatic throttle range calibration, easy to use.
- Easy to set the ESC parameters with jumpers.
- Multiple protections: Low voltage cut-off protection for battery / Over-heat protection / Throttle signal loss protection.
- Model: ESC-1060WP
- Fwd. Cont. / Peak Current: 60A /360A
- Rev. Cont. / Peak Current: 30A /180A
- Voltage Range: 2-3S Lipo or 5-9 NiMH
- Cars Applicable: 1/10: Touring Car, Buggy, Short Course Truck, Monster, Truggy, Rock Crawler and Tank
- 2S Lipo or 6 NiMH
- 540 or 550 Size Motor: ≥12T Or RPM<30000 @7.2V
- 3S Lipo or 9 NiMH
- 540 or 550 Size Motor: ≥18T Or RPM< 20000 @7.2V
- 4S Lipo or 12 NiMH
- Resistance: Fwd 0.001Ω, Rev 0.002Ω
- BEC Output: 2A/5V (Linear Mode)
- PWM Frequency: 1KHz
- Dimension / Weight: 36.5*32*18 / 39g
- Cooling Fan: Without cooling fan
- Running Modes: Forward/Reverse/Brake, Forward/Brake, Forward/Reverse
- Yeah Racing Tritronic 1/10 Waterproof Brushed 60A ESC (1 Set)
- Manual (1 pc)
Yeah Racing Hackmoto V2 13T 540 Brushed Motor #MT-0012
This Yeah Racing Hackmoto V2 Modified brushed motor series are high performance 540 motors designed exqusitivly for competitive RC usage.
Hackmoto V2 featured premium quality material with high strength magnets for unmatched brushed motor speed and torque. Beside of its performance, the motor featured direct-solder wiring tabs for flexible soldering options. It is also designed to be rebuildable with an easily accessible commutator and replaceable brushes and springs. The motor also adapted dual-ball bearings design yields better performance, allowing a smooth ride, precise control with best possible efficiency.
- Size: 540
- For: 1/10 RC Car
- Color: Black
- Rebuildable with an easily accessible commutator and replaceable brushes and springs
- High strength magnets for unmatched brush-motor performance
- Specifically designed for R/C vehicles that require precise movement control
- Excellent torque and long-run times
- Direct-Solder Wiring Tabs for flexible soldering options
- Dual-ball Bearings Design
- Length: 70mm
- Width: 36mm
- Shaft: 3mm
- Turn: 13
- Input Voltage: 7.4v
- Max. Input Voltage: 11.1V
- Shaft Length: 13mm
- Yeah Racing Hackmoto V2 13T 540 Brushed Motor (1 pc)
Onisiki 2.4GHz 2 Channel 2.4Ghz Transmitter w/ Receiver #ONI3701
*Photos for reference only.
Onisiki's 2 channel 2.4Ghz Radio Kit with a receiver that features failsafe function which aims to prevent any accidents if your battery runs out on either on receiver or transmitter. If the Receiver is not able to receive any signal, from the control to Throttle, the parameter of Throttle on Receiver will turn back to its original setting! Features dual rate control and servo reverse for any custom rc enthusiast!
- For: RC Cars and Boats
- Transmitting Frequency: 2.4GHz
- Transmitter Channels: 2 Channels
- Receiver Channels: 3 Channels
- Operation method: Wheel + trigger type
- Frequency: 2.40-2.48GHz
- Code type: GFSK
- Bandwidth: 500Hz
- Band: 160
- RF Power: Less than 20DB
- 2.4G System: AFHDS
- Sensitivity: 1024
- ST Range: 90
- TH Range: 45 (F:30; B:15)
- Transmitter Colour: Black and Red
- Transmitter Material: Plastic
- Receiver Material: Plastic
- Power: 3.7V DC
- Size: 224 x 156 x 94.5mm
- RF. receiver sensitivity: -100dbm
- Input Voltage: 4.5-6vdc
- ANT length: 33mm
- Size: 37.6 x 22.3 x 13mm
- Onisiki 2.4GHz 2 Channel 2.4Ghz Transmitter (1 pc)
- Onisiki 3 Channel 2.4GHz Receiver (1 pc)
- TX Antenna (1 pc)
- Bind Plug (1 pc)
- Manual CD (1 pc)
- AA Battery for Transmitter (4 pcs)